Leading provider
of high-performance wire,
cable and tubing since 1959
Toll Free:(800) 822-WIRE
Local: (661) 257-2400
  • Unique cable design: The braid configuration and the expanded PTFE dielectrics of the LL cable constructions contribute to lower attenuation levels at higher frequencies, while providing shielding effectiveness levels that exceed those of flexible MIL-C-17 cables. Flat strips of silver plated copper are braided over the dielectric core with an intermediate metallized polyester or polyimide layer, and an outer round wire braid.
  • Improved electrical characteristics: LL cables with expanded PTFE dielectrics exhibit low coefficients of expansion over the entire operating temperature range from -100° C to +250° C. Impedance discontinuities are minimized at the cable- to-connector interface. Higher levels of power can be transmitted because higher temperatures do not affect the cable due to the temperature stability of the tape. Where phase versus temperature requirements are critical, LL cables allow for an approximately 75% lower phase shift and change in propagation time delay due to temperature. Temperature cycling tests have been performed on a number of cables with positive results.
  • Lowest attenuation for any given size: LL coaxial cables, with expanded PTFE dielectrics and strip braid composite configurations, offer attenuation from 20 to 35% below other mil spec cables of comparable size. When size and weight are considerations, LL cables should be considered. The graph below defines maximum attenuation levels for all LL cables referenced on the next page.
  • Technical support available: We continually work with cable assembly houses and connector manufacturers to ensure maximum system reliability. Cable designs take into consideration size and weight constraints, existing connector availability and termination techniques. Sources of supply for connectors operative to 18 GHz may be recommended.
  • Many special constructions available: The chart on the following page outlines just a few designs we have manufactured. Some of the more popular constructions are standard stock items, and many additional cables are available for prototype assemblies. Additional cables not referenced here are available to meet specific customer requirements.
    • Unit of Measure

    Specifications

    Construction

    		 N/A Center Conductor: Silver plated copper, solid or stranded Dielectric: Expanded PTFE tape Inner Braid: Flat silver plated copper strip Inter layer: Aluminum polyester or polyimide tape Jacket: FEP, translucent colors, solid colors or clear Outer Braid: Round silver plated copper

    Center Conductor

    		 N/A 0.0285 inch Solid

    Dielectric Diameter

    		N/A 0.080 in

    Diameter Over Inner Braid

    		 N/A 0.086 in

    Diameter Over Interlayer

    		 N/A 0.092 in

    Diameter Over Outer Braid

    		 N/A 0.108 in

    Overall Diameter

    		 N/A 0.120 in

    Weight

    		 N/A 17.00 lb/1000 ft.

    Min. Recommended Bend Radius

    		 N/A 0.60 in

    Put-up

    		 N/A 30 inch wood, multiple lengths per spool

    Operating Temperature

    		 N/A -55 to +200 ºC

    Electrical Characteristics

    Impedance

    		 N/A 50 ohms

    Capacitance

    		 N/A 25.0 pF/ft

    Velocity of Propagation

    		 N/A 80.0 %

    Attenuation @ 400 MHz per 100 ft.

    		 N/A Typical: 9.0 dBMaximum: 12.0 dB

    Attenuation @ 1 GHz per 100 ft.

    		 N/A Maximum: 18.0 dBTypical: 14.6 dB

    Attenuation @ 2 GHz per 100 ft.

    		 N/A Maximum: 25.0 dBTypical: 21.0 dB

    Attenuation @ 3 GHz per 100 ft.

    		 N/A Typical: 25.6 dBMaximum: 30.0 dB

    Attenuation @ 5 GHz per 100 ft.

    		 N/A Typical: 32.0 dBMaximum: 38.0 dB

    Attenuation @ 10 GHz per 100 ft.

    		 N/A Typical: 48.0 dBMaximum: 54.0 dB

    Attenuation @ 18 GHz per 100 ft.

    		 N/A Typical: 61.5 dBMaximum: 74.0 dB
    Request Information